WINS CLIENT SPACE
RVI underground storage tank (UST) inspection (VIDEO)
President Tom Hay presents at Acoustic Emission Working Group (AEWG-54) meeting in Baltimore, MD, May 2012
President Tom Hay delivers talk on NDT Applied to Bridge Inspection at Association for Bridge Construction & Design (ABCD) in Batavia, NY, April 2012
New remote visual inspection (RVI) capability - Video
DOT special permit approval for Acoustic Emission Retesting of 107A tubes
New pipeline inspection technology for Splashtron coated pipes
2013 NDT Training Course Calendar
Thermite Weld Testing Services
We provide comprehensive testing services for assuring quality of welds of all types of rails manufactured to current AREMA specifications. These testing services cover both the initial process qualification and as well as routine QA requirements.
Tests are preformed at our facilities in State College, PA by experienced and qualified personnel. Test results are provided at normal and quick turnaround times.
The different thermite weld testing services provided by WinS are:
WavesinSolids provide chemical analysis of rails to identify the presence and the amounts (by weight percent) of the following elements: Carbon, Manganese, Phosphorous, Sulfur, Silicon, Nickel, Chromium, Molybdenum, Vanadium and Aluminum. Optical Emission Spectroscopy (OES) analysis is performed to determine the chemical composition of the rails and evaluated with respect to the standards specified in AREMA Manual for Railway Engineering Chapter 4. OES is the reference technique for elemental analysis of solid metallic samples and is capable of performing rapid simultaneous analysis of up to 60 elements.
Slow Bend Test & Bond Integrity
The rail is supported on a 72" span with the weld joint centered between the supports, and central static load is applied.
For vertical loading, dial gages used to record vertical deflection, are located 3" on either side of the central loading point and on the center of the rail base.
For lateral loading, the load is applied at the center of the span through the rail's neutral axis, and the deflections at rail head and at edge of rail base are recorded by dial gages located 3" on either side of the loading point.
Bond integrity is determined from the fracture faces of the slow bend test samples. AREMA manual stipulates that the bond between two joining rail ends shall not contain no more than one inch diameter discontinuity.
Weld Hardness Testing
Brinell Hardness Test (prescribed by ASTM E 10) to carry out precise measurement of the diameter of an indentation made with hardened balls of various diameters under various loads is performed. We provide the optics and analysis software (Digital Optical Comparator System) for the required diameter measurement and subsequent calculation of the Brinell hardness in accordance with the ASTM standards.
WINS utilizes several techniques for preparing material samples for analysis including metallographic preparation for either micro-structural or macro-structural analysis. Macro-etching involves taking a cross-section of the large component, grinding and polishing the surface and etching the piece and then, visually analyze the degree of micro-structural segregation.
WINS also provides micro-structural analysis using scanning electron microscope (SEM) and other microscopic techniques.
Magnetic Particle Testing
WINS uses standard magnetic particle equipment for testing of thermite welds. The inspection procedure follows the recommendations outlined in ASTM E709 - 08 i Standard Guide for Magnetic Particle Testing. The procedure may vary depending on the rail type, profile, surface condition, etc. AC electromagnetic yokes are used.
Angle-beam transducers are used to introduce ultrasonic energy into the rail, This mechanical energy travels down the rail and interacts with rail defects, ends, weld defects and various surface conditions. Upon encountering one of these discontinuities, a portion of the wave will be reflected back towards the transducer as well as transmitted through the discontinuity. The amount of energy reflected and transmitted will depend on the size and shape of the defect. WINS have state-of-the-art ultrasonic instrumentation and wide variety of wedges and transducers to perform rail weld testing.
WINS also provide Hy-Rail vehicle mounted technology for ultrasonic inspection of rail heads for transverse defects.
Internal and Surface Hardness Testing
WINS perform surface and internal rail hardness tests in accordance with ASTM standard E18. The hardness measurements are undertaken with a Rockwell C superficial surface and standard Rockwell C hardness testing machines. The Rockwell C values are converted to Brinell Hardness values using the conversion table in the AREMA Manual.